Coleman 8200 Series Especificações

TECHNICAL MANUALFORDYNA 8000, 8200 & 8400ELECTRONIC GOVERNORDYNA 8000DYNA 8200DYNA 8000-400 & DYNA 8400-400DYNA 8400F-23721-5

Side View"On"ON OFFSide View"Off"OFFONONOFFTop ViewS1 S25.5 PROPER PROCEDURES FOR SETTING SWITCHES S1AND S2Question: How do I kn

6. CALIBRATION PROCEDURE FOR 8000 GOVERNOR CONTROLLER —DYN1-10682, 10683, 10684, 10686DYN1-10682-000-0-12/24DYN1-10682-001-0-12/24*DYN1-10683-000-0-12

Side View"On"ON OFFSide View"Off"OFFONONOFFTop ViewS1 S2126.5 GENERAL INFORMATION ON S1 AND S2• Switch S1 selects one of two inte

7. DYNA 8000 SERIES TROUBLESHOOTING CHART7.1 PROBLEM: GOVERNOR IS COMPLETELY DEAD AND ACTUATOR LEVER STAYS AT MINIMUM POSITIONWHEN POWER IS APPLIED

Means of Detection Corrective ActionVerify and correct wiring as necessary.Verify and correct wiring as necessary.Replace controller.If continuity is

7.5 PROBLEM: SLOW, SMALL AMPLITUDE HUNTING OF SPEED OR FREQUENCYMeans of Detection7.5.1 Sticking or very loose linkage.Corrective ActionCorrect Linka

16DYNC-11024-000ACTUATOR —COUNTERCLOCKWISEROTATIONDYNC-11024-300SIDE MOUNTEDACTUATOR —COUNTERCLOCKWISEROTATIONDYNC-12000-000

DYNC-14800-000TERMINAL STRIP CONNECTIONDYNC-14801-0002-PIN MS CONNECTOR CONNECTION17DYNC-11020-401UL APPROVAL, HAZARDOUS DUTY, CLASS 1, DIVISION 2, GR

DYNC-11024-400UL APPROVAL, HAZARDOUS DUTY, CLASS 1, DIVISION 2, GROUP DCOUNTERCLOCKWISE UNITDYNC-14800-400UL APPROVAL, HAZARDOUS DUTY, CLASS 1, DIVISI

CONTENTSSECTION DESCRIPTION PAGE1 GENERAL INFORMATION... 32 SPECIFICATIONS... 33 FUNCTIO

=Input SignalFrequency in Hertz32.1.10 DYNA 8000 CONTROLLERNominal Quiescent Current 80 mAMaximum Amperes @ Stall 13 ampsNominal Quiescent Current 80

2.2.11 AVAILABLE DYNA 8000 HAZARDOUS DUTYACTUATOR MODELS WITH CLOCKWISE OUTPUT SHAFTROTATION (Standard Mounted Units)• DYNC-11020-400-0-12 Standard C

Current @24 VDCCurrent@12 VDCWeightOutputTorqueWorkNominal Response Time for 63% of Stroke(Seconds) .138WorkTorqueOutputWeightCurrent @24 VDCNomina

Full LoadEngine RPMNo LoadEngine RPMAdjustable100%% of Engine Load0%EngineRPMNOTEMounting information and kits are usually available fora particular e

4.2.1 ROTARY ACTUATOR TO ROTARY FUEL PUMP4.2 TYPICAL LINKAGE ARRANGEMENTS FOR THE ACTUATOR AND FUEL SYSTEM4.2.2 ROTARY ACTUATOR TO LINEAR FUEL PUMP

† The 5K remote speed potentiometer can be wired two different ways:1. As shown by the solid line from the wiper of the 5K potentiometerand then conne

2500 to 5000 Hz5000 to 9000 HzDYN1-10652-000-0-12/24DYN1-10652-001-0-12/24*DYN1-10653-000-0-12/24DYN1-10653-001-0-12/24*]] 250 to 1200 Hz1200 to 2500